Información técnica y de seguridad
- Base portadora
- Otro
- Base química
- Aceite
- Color
- Transparente
- Presentación
- Available formats on request
- Pedido mínimo
- Consultar
Etiquetado y seguridad
Revisión de la FDS: GHS 4.0 — 09.02.2026
Palabra de advertencia: Peligro
Indicaciones de peligro
- H226: Líquidos y vapores inflamables.
- H304: Puede ser mortal en caso de ingestión y penetración en las vías respiratorias.
- H336: Puede provocar somnolencia o vértigo.
Consejos de prudencia
- P210: Mantener alejado del calor, de superficies calientes, de chispas, de llamas abiertas y de cualquier otra fuente de ignición. No fumar.
- P261: Evitar respirar la niebla/los vapores/el aerosol.
- P301+P310: EN CASO DE INGESTIÓN: Llamar inmediatamente a un CENTRO DE TOXICOLOGĺA/médico.
- P303+P361+P353: EN CASO DE CONTACTO CON LA PIEL (o el pelo): Quitar inmediatamente toda la ropa contaminada. Enjuagar la piel con agua o ducharse.
- P331: NO provocar el vómito.
- P370+P378: En caso de incendio: Utilice arena seca, polvo extintor o espuma resistente al alcohol para extinguir.
- P403+P233: Almacenar en un lugar bien ventilado. Mantener el recipiente cerrado herméticamente.
Información suplementaria
- EUH066: La exposición repetida puede provocar sequedad o formación de grietas en la piel.
Componentes peligrosos para el etiquetado
Hydrocarbons, C9-C11, n-alkanes, isoalkanes, cyclics, <2% aromatics, Destilados (petróleo), fracción parafínica pesada tratada con hidrógeno, Distillates (petroleum), hydrotreated light paraffinic
Documentación
Ficha técnica en español Ficha de datos de seguridadLas fichas técnicas se sirven desde Coapsys y se obtienen de la fuente oficial Tectyl Europe.
Tectyl 283-S-17 is a solvent cutback, water displacing, oil-based corrosion preventive compound, lubricant and penetrant. The cured film is an ultralight, transparent, non-staining oil. Tectyl 283-S-17 is used to protect industrial parts during long-term indoor or covered storage, and during domestic shipment.
Benefits and application considerations
- Excellent protection Tectyl 283-S-17 protects your parts during storage and domestic transport against corrosion.
- Economical solution With the thin layer of only 1,5 microns a large area can be protected against corrosion.
- Water displacing and non-staining Tectyl 283-S-17 displaces water where needed and leaves no stains while protecting your parts against corrosion.
Technical characteristics
- Carrier
- Oil
- Recommended Dry Film Thickness — Over metal profile
- 2 µm
- Corrosion — ISO 9227 NSS (min. days)
- 5 days
- Humidity — Humidity; 100 % RH; @ 40°C; ISO 6270-2 CH (Q-Panels, Type R, ASTM A1008)
- 75 days
- Protection Indoor — (min. months)
- 12 months
Surface preparation
The maximum performance of Tectyl 283-S-17 can be achieved only when the metal surfaces to be protected are clean, dry and free of rust, oil and mill scale. CorPro recommends that the metal substrate temperature be 10-35 °C at the time of product application.
Application
Tectyl 283-S-17 is formulated to be used as supplied. CorPro recommends that the ambient and product temperature be 10-35 °C at the time of product application. Do not thin Tectyl 283-S-17. Tectyl 283-S-17 can be applied by low pressure air spray or dipping. Details on application can be found in the application chart. If the product thickens due to cold storage or loss of solvent during use, contact CorPro.
Removal
In the wet and dry phase Tectyl 283-S-17 can be removed with Tectyl Biocleaner or Tectyl 150.
Check the current official Technical Data Sheet and Safety Data Sheet before purchase or use. Coapsys can advise on product selection and application equipment.