Información técnica y de seguridad
- Base portadora
- Agua
- Base química
- Dispersión acuosa
- Color
- Transparente
- Presentación
- Available formats on request
- Pedido mínimo
- Consultar
Etiquetado y seguridad
Revisión de la FDS: GHS 8.0 — 09.02.2026
Palabra de advertencia: Atención
Indicaciones de peligro
- H319: Provoca irritación ocular grave.
Consejos de prudencia
- P264: Lavarse las manos concienzudamente tras la manipulación.
- P280: Llevar gafas/máscara de protección.
- P305+P351+P338: EN CASO DE CONTACTO CON LOS OJOS: Enjuagar con agua cuidadosamente durante varios minutos. Quitar las lentes de contacto cuando estén presentes y pueda hacerse con facilidad. Proseguir con el lavado.
- P337+P313: Si persiste la irritación ocular: Consultar a un médico.
Información suplementaria
- EUH208: Contiene Cobalt bis(2-ethylhexanoate). Puede provocar una reacción alérgica.
Documentación
Ficha técnica en español Guía de aplicación Ficha de datos de seguridadLas fichas técnicas se sirven desde Coapsys y se obtienen de la fuente oficial Tectyl Europe.
Tectyl 300G Clear E is a waterborne corrosion preventive coating. The cured film is hard, transparent and flexible. Tectyl 300G Clear E provides an effective barrier against corrosive environments for ferrous and non-ferrous fabrications and industrial components.
Benefits and application considerations
- Excellent flexibility Due to its mechanical properties, the surface is protected over a long period of time, even with a 180° Mandrell bend.
- Overcoatable Tectyl 300G Clear E is recoatable with topcoat systems. Test on a small area first to ensure compatibility between Tectyl 300G Clear E and the topcoat.
- Final result Tectyl 300G Clear E leaves an excellent transparent finish that facilitates visual inspection of the surface.
- Can be applied almost anywhere Due to the transparent, flexible coating, Tectyl 300G Clear E can be used almost anywhere.
Technical characteristics
- Carrier
- Water
- Recommended Dry Film Thickness — Over metal profile
- 50 µm
- Corrosion — ISO 9227 NSS (min. days)
- 21 days
- Humidity — Humidity; 100 % RH; @ 40°C; ISO 6270-2 CH (Q-Panels, Type R, ASTM A1008)
- 21 days
- Protection Indoor — (min. months)
- 36 months
- Protection Outdoor — (min. months)
- 12 months
- Weathering — ASTM G23 (min. hours)
- 500 hours
- Mandrel Bend — 180°
- PASS
Surface preparation
The maximum performance of Tectyl 300G Clear E can be achieved only when the metal surface to be protected are clean, dry and free of rust, oil and mill scale. CorPro recommends that the metal substrate temperature be 10-35 °C at the time of product application.
Application
Tectyl 300G Clear E is formulated to be used as supplied. Ensure uniform consistency prior to use. If the product thickens due to cold storage or loss of water and coalescing during use, contact CorPro. Do not thin Tectyl 300G Clear E. Incorrect thinning will affect film build, dry time and product performance. Tectyl 300G Clear E can be airless spray or dip applied. Details on application can be found in the application chart.
Removal
Tectyl 300G is not intended for removal. In the wet phase Tectyl 300G in the wet phase can be removed with water or Tectyl Biocleaner. If dried and cured the film can be removed with ethyl acetate.
Check the current official Technical Data Sheet and Safety Data Sheet before purchase or use. Coapsys can advise on product selection and application equipment.